|
零件名稱 |
材 料 Material |
|
|
Name of parts |
用于海水Use for sea water |
用于淡水Use for fresh water |
|
泵體Pump
body |
ZCuZn16Si4(GB1176-87) |
QT450-10(GB1348-88) |
|
葉輪Vane
wheel |
ZCuZn16Si4(GB1176-87) |
ZCuZn16Si4(GB1176-87) |
|
泵蓋Pump
cover |
ZCuZn16Si4(GB1176-87) |
QT450-10(GB1348-88)
|
|
軸承支架Bearing bracket |
QT450-10(GB1348-88) |
QT450-1O(GB1348-88)
|
|
電機架Motor bracket |
QT450-10(GB1348-88) 或Or
Q235-A(GB700-88) |
QT450-10(GB1348-88) 或Or
Q235-A(GB700-88) |
|
軸Shaft |
1Cr18Ni9Ti(GB1220-84) |
1Cr18Ni9Ti(GB1220-84)
|
|
密封環Sealed ring |
ZCuZn16Si4(GB1176-87) |
ZCuZn16Si4(GB1176-87) |
|
葉輪鍵Vane wheel key |
1Crl8Ni9Ti(GB1220-84) |
1Cr18Ni9Ti(GB1220-84) |
|
螺栓Bolt |
1Cr18Ni9Ti |
Q235-A |
|
螺母Nut |
H62 |
Q235-A |
4.1運轉前準備
Preparation for operation
4.1.1啟動前應卸下聯軸器護罩，用手扳動聯軸器數圈，確信無碰擦現象后再裝好聯軸器護罩。
Before starting the pump，take off the cover of the
coupler,then turn the coupler by hand，and make sure
that it can revolve smoothly．Last put the cover back．．
4.1.2每次啟動前應將泵注滿水，嚴禁沒加水運轉，防止磨壞軸封。(帶自吸裝置時不須注水)．
Before starting the pump，it must be filled up with water．Operation without water filled up into the pump body is forbidden．[the pump with self-suction device do not need to filled up]．
4.1.3點動電動機，檢查電機轉向是否符合泵的轉向標志。
Start the motor and examine whether its revolution direction is the same
as indicated on the pump body．
4.2運轉中注意事項．
Precaution during operation
4.2.1泵起動前應關閉出口閥門，泵開始排水后，逐漸調節出口閥門，
|